Having refrigerator problems is something no one prepares for, even if it is a light problem. Fortunately, this article helps you to fix KitchenAid refrigerator light problems.
Table of Contents
KitchenAid Refrigerator Light Not Working – Solved
The entire light assembly may be faulty, but before determining that, check individual parts. Start with the light bulb, which is the most likely part ot fail. Ensure it is properly screwed into the light socket; otherwise, it will not work. Also, check the socket, especially if the bulb is in good working condition. Its wire connection may be loose or weak, or the socket may fail.
Furthermore, test the door or light switch to check its functionality. If everything checks out, you may have to replace the light assembly, although the light control board may malfunction and affect the light. Check out this article on a KitchenAid refrigerator light not working to find helpful resources to troubleshoot and fix the problem.
Note: The same steps apply to all KitchenAid refrigerator models. If a KitchenAid refrigerator freezer light is not working, you may have to check the control module because the light is usually LED. Replace the bulb and if the problem continues, test the module and replace it if necessary.
How to Turn Off the Replace Filter Light on a KitchenAid Refrigerator
Turning off the Replace Filter light on a KitchenAid refrigerator means resetting it. While a few models automatically reset after the filter replacement, others do not. You must manually reset the filter light after replacing the water filter because it does not automatically reset. How you do this depends on the refrigerator model, as several reset methods exist for different models.
Some KitchenAid refrigerator models have a dedicated reset filter button on the control panel. So, check the panel or consult the user manual to determine whether or not your model has this button. Press and hold the Filter Reset button until the Replace Filter light goes off, indicating that the system has reset.
A few models have a Water Filter button that serves the same purpose of resetting the filter light. Immediately after replacing the filter, press and hold this button for about three seconds. The light on the water filter icon should change to blue from orange or red, and the Replace Filter showing on the screen should disappear. However, if none of the above buttons exists on your KitchenAid refrigerator model or pressing them does not work, there are other ways to reset the filter light.
Locate the Options button on the control panel. If there is one, press it once and press the Filter reset button. Then, press the Measured Fill button to complete the process. The filter indicator should turn off when the reset is successful and complete. Do this every time you replace the water filter. Another method to try is using the Max Ice and Max Cool buttons.
Press them simultaneously and hold them for about three seconds. The display should show a countdown from three to one, flash the water filter icon, and beep a tone as it resets. But if these do not apply to your refrigerator model, check for the Ice Type and Light buttons on the control panel. If your model has them, press both simultaneously and hold them for about three seconds. The filter indicator should go off when the system resets.
It is best to follow the water filter reset instructions in your refrigerator user manual, especially if there are no dedicated buttons for that purpose. You must replace the filter and reset the light every six months, sometimes within a shorter time, depending on the water quality in the area. And ensure you flush the system to prevent trapped air, which can affect the water system. Simply dispense about 15 glasses of water to clear the trapped air.
Not every refrigerator with a water filter has an indicator or light to alert you when it is due for a replacement. If you have a refrigerator model with an indicator, it alerts you, relieving you from manually counting the months. However, you must time the filter and replace it after six months without an indicator.
The refrigerator’s water flow to the ice maker and water dispenser typically decreases when the filter needs replacement because dirt clogs and restricts the water. You may also notice the ice tasting bad or the water having dirt. Always use an Everydrop or Whirlpool-branded water filter for your KitchenAid refrigerator for the best results.
How to Change the Light Bulb in a KitchenAid Refrigerator
Changing the light bulb in a KitchenAid refrigerator is straightforward. Follow the steps in this article on a KitchenAid refrigerator 40-wattage light bulb replacement to change the bulb in your specific model. Note that you must determine the correct wattage for your model; not every refrigerator uses a 40-watt bulb.
KitchenAid Refrigerator Lights Flashing – What to Do
A KitchenAid refrigerator has several lights that can flash if there is a fault. If the interior lights are flashing or blinking, it may have to do with the control module or the light control board. You can easily replace these parts if faulty, but you must ensure they need a replacement. You may need an appliance technician to determine whether or not the module or control is defective.
The air filter status light may also blink on the control panel if the filter is due for a replacement. You may consult the refrigerator’s user manual for specific instructions to reset the filter light. But in many models, you will find an Air Filter button. Press and hold it for about three seconds to reset the status light. That should stop the light from flashing.
If the filter icon turns blue, the reset is complete, and the filter works well. You should replace the filter when the icon turns yellow or red, and Replace Filter appears on the refrigerator’s display. However, replacing the filter is crucial if the icon becomes red and Replace Filter flashes. You must use the correct replacement parts for your KitchenAid refrigerator.
Door Open Alarm Light
The door alarm may blink on the control panel if the door is open for longer than two minutes. It will alert you, together with an audible alarm, that the door is open and the refrigerator is losing cold air. The light will blink until you close the door and the refrigerator’s internal temperature returns to food-safe levels.
Other issues that may cause the door alarm light to flash are an improperly leveled refrigerator and a weak door gasket. Ensure the refrigerator is level; place a level on top of it and check the bubble. Adjust the alignment screws under the unit following the instructions in the user manual. Also, check the gasket for wear; clean it if dirty or replace it if weak. You may have to limit how often you open the refrigerator until the temperature drops so the alarm light stops flashing.
Power Outage
The refrigerator may also have flashing lights if there is a recent power outage. The display typically shows PO, and it flashes with a tone to alert you to the power outage situation. You must confirm or acknowledge the outage before the flashing error stops and the refrigerator stops beeping. Simply press any button on the control panel to stop the flashing error and another button to return the display to the home screen.
Water Filter Light
As mentioned earlier, the water filter light turns from blue to orange or red once the filter is due for a replacement. However, the light flashes red if you do not replace the filter after the status changes. If that is the case, immediately replacing the filter is crucial to keep the water pure and the flow unrestricted.
Therefore, get a new filter compatible with your KitchenAid refrigerator model and replace the old one. Then, reset the filter light following the instructions in the user manual to finish the process. Your refrigerator may need service if you cannot reset the filter light. Contact the KitchenAid Service Center to schedule service or hire an independent appliance technician for the job.
Temperature Alarm Light
The Over Temp alarm may go off if the temperature in the refrigerator or freezer becomes too high. The refrigerator’s temperature should typically be between 33 and 40 degrees Fahrenheit, and the freezer should be between 0 and 5 degrees Fahrenheit for the best results. If the freezer temperature rises above 15 degrees Fahrenheit or the refrigerator rises above 48 degrees Fahrenheit, the Over Temp alarm alerts you to the temperature change.
Several issues can cause a temperature change in the refrigerator, but ensure the doors are tightly shut. You can turn off the light by pressing the Alarm button to indicate you are aware of the temperature rise, but the audible alarm will keep beeping until the internal temperature returns to normal. Determining the reason for the temperature issue is crucial to prevent a future occurrence.
Cooling Off Indicator Light
Every KitchenAid refrigerator has a cooling function that must work if the refrigerator must cool. However, not every model has a dedicated icon or button to indicate when the cooling function is on or off. The light will flash if the cooling function is off for models with a cooling-off indicator. At this point, the display will show Cooling Off, and you must follow the user manual instructions to turn the cooling function on again and turn off the flashing light. And if there is a problem with the refrigerator cooling, contact the KitchenAid Center for further assistance.
Sometimes, the refrigerator will flash the F error code. If this happens, reset the refrigerator to fix the error. Disconnect it from electric power by turning off the circuit breaker. Wait a minute and turn the breaker on again. Ensure the cooling function is on and wait to see if the error code reappears. If it does not, the problem is solved. However, if the F error code appears after the reset, contact KitchenAid to schedule service.
KitchenAid Refrigerator Door Open Light Flashing – Fixed
Sometimes, the refrigerator or freezer door may not be properly closed if the door ajar light flashes. A beeping alarm tone may accompany the flashing light. If that is the case, you must check the door to ensure it is tightly shut. Rearrange the contents of the freezer and refrigerator contents, and ensure no shelf, rack, or bin sticks out.
Also, check the door gasket and clean it if it has stains. A dirty gasket can keep the door from fully closing, and cleaning it can fix the problem use warm soapy water. Scrub the gasket with a soft sponge, but replace it if it is weak or torn. In addition, level the refrigerator if it is unbalanced, and use shims if the floor is uneven.
A final possibility is that the control board is faulty. If the problem persists after fully shutting the door and ensuring no refrigerator or freezer content sticks out, you may want to check the control board. The board controls how the refrigerator functions, including the alarms. So, if it keeps flashing, you may have to replace the board. Hire an appliance technician to check the door open light and see if the problem can be fixed by replacing the light. Otherwise, the technician should test the board to determine whether or not it needs a replacement.
Note: These steps also apply if your KitchenAid refrigerator door light stays on when the door is shut.
Check out these other articles…
KitchenAid Refrigerator Making Noise [Proven Solutions]
KitchenAid Double-Door Refrigerator Noise [Issues Solved]
KitchenAid Refrigerator Wattage [In-depth Guide]
How to Remove a KitchenAid Refrigerator… [Detailed Guide]
KitchenAid Refrigerator Flashing/Blinking/Flickering [Proven Solutions]
KitchenAid Refrigerator Flashing PO – Quick Fix
When you see PO on the control panel’s display on your KitchenAid refrigerator, it means there has been a recent power outage. It is designed to alert you when there is no power supply to the appliance and the internal temperature is rising. It is nothing to worry about; ensure the doors are closed and the cooling function is working.
Then, press any button on the control panel to confirm the outage. Press any other button to stop the audible alarm. The PO error on the refrigerator’s display may flash until the temperature drops to the normal point. You may also want to check the refrigerator’s user manual for other instructions in resetting the PO error code.
KitchenAid Refrigerator Flashing 01 – Quick Fix
The refrigerator may be in service test mode if it is flashing 01. The code usually means the refrigerator passes that particular test, but you must determine why it is in that mode if you did not manually activate it. Your user manual contains instructions on putting the appliance in service or diagnostic mode, but you can also contact the KitchenAid Service Center or employ the services of an appliance technician to determine why it is in service mode.
KitchenAid Superba Refrigerator Ice Maker Blinking Red Light – Solved
Ensure nothing blocks the ice maker sensor. The sensor detects the ice level in the storage bin and alerts the ice maker when to make ice or stop ice production. If the sensor is dirty or obstructed, the red status light flashes to signify an issue. Therefore, check the ice scoop to ensure it is not obstructing the sensor. Also, dirt may cause the sensor to stop working. So, clean it and see if the light stops flashing.
If the problem persists, check the water filter. The filter ensures there is a clean water flow in the refrigerator, to the dispenser, and to the ice maker. Over months of use, the filter clogs with dirt and restricts the water flow. This becomes a problem for the water supply to the ice maker. If you live in a busy house where the ice maker is frequently used, you may want to replace it once every four months. But if not, replace it every six to eight months; ensure you use the correct filter type and follow the installation instructions in the user manual.
However, you may have to reset the machine if the red status light keeps blinking after replacing the water filter. Ensure the ice maker’s switch is on or use the metal arm to keep it in the On position. Next, turn off the refrigerator light by pressing the door switch. Close the door and wait about ten seconds before opening it again. Press the door switch when you open the door this time, but press it three times in quick succession and close it again. The red light should stop blinking.
Ensure there is no ice jammed in the ice maker, keeping the ejector blades from moving. The red light may blink if the machine is clogged with ice or the sensor is obstructed with ice. Additionally, do not store anything in the ice bin to prevent obstructing the sensor or damaging the ice bin. But if none of these works, you may have a faulty ice maker control board. Get an appliance technician to troubleshoot further and fix the problem.
Important Notes
These steps apply to all KitchenAid refrigerator models. If the ice maker stops making ice when the red light blinks, you may want to ensure there are no ice clumps in the storage bin. Also, ensure the bin is not too full; reduce the ice stored in it because it may trigger the ice maker to stop production. Check the water supply and flush the system by dispensing a few glasses of water after replacing the water filter.
KitchenAid Refrigerator Light Bulb Cover Removal
The steps to remove the light bulb cover or light shield in a KitchenAid refrigerator depend on the model. Some models have light bulb covers you can slide off, while others have covers with tabs you must unlock before removing the bulb. Newer and more sophisticated models may have a different method.
Some may have screws holding the light cover in place; inspect the shield to determine how it is secured. Therefore, consult the refrigerator’s user manual or find online manuals for your specific model if the manual is no longer available. You can also contact KitchenAid for advice or assistance if you need a handy manual for your specific model.
KitchenAid Refrigerator Beeping With No Light – How to Fix
Several issues can cause a KitchenAid refrigerator to beep with no light. The first thing to check is the door or light switch; it turns the interior lights on and off. The door pushes it in and triggers it to turn off the light. However, if the door no longer pushes it in far enough, it may cause the light to stay off. As a result, the refrigerator reads it as ‘door open,’ triggering the beeping, which is the door open alarm.
Therefore, open the door and manually press the switch. Doing this activates it; you should see if the light responds. If that happens, it means the door switch is loose; you must find a small object to depress it whenever you close the door. That may mean taping the object temporarily over the switch until you find a permanent solution.
There is also the possibility that the door has been open for too long. Typically, a KitchenAid refrigerator triggers the Over Temp alarm to alert you when the door has been open for more than ten minutes. That means the internal temperature is rising, and you need to close the door. Press the Over Temp button on the control panel once or twice to stop the beeping and turn the light on again. Ensure nothing obstructs the door from fully closing; you may have to organize your refrigerator for proper door closing. Also, check the door gasket to ensure it is working.
However, if none of the above works, check the evaporator coils. Ice on the coils prevents cold air release, which may affect how the refrigerator functions. This is especially true if you notice the refrigerator is not cooling or the freezer has too much ice. Turn off the refrigerator and open the doors to allow the ice to thaw. That should fix the cooling problem and turn on the lights. You may have left the door open for too long, causing too much condensation that freezes and the light to go off.
You must also check the defrost system if the refrigerator has an automatic one. Troubleshoot further to determine why there is an ice accumulation and fix the problem. You may need an appliance technician because the problem may be overheating issues in the condenser, compressor issues, fan motor issues, and door gasket issues.
Note: Manually defrosting the freezer by leaving the door open for a few hours solves the problem of a KitchenAid French-door refrigerator with the freezer light out and frost everywhere.
KitchenAid Refrigerator Door Open Light Stays On – Quick Fix
As mentioned, one of the primary reasons the door open light on a KitchenAid refrigerator stays on is if the door gasket is weak. Another reason is if an item is pushing the door open, sometimes due to poor organization of contents. So, you must check these factors to determine whether or not they apply. Replace the door gasket if it is weak and does not seal the door tightly anymore. Otherwise, check to see if it is dirty and clean it with warm soapy water. Also, rearrange the refrigerator and freezer contents so no item or shelf is out of place.
However, if everything is in place, but the door open light stays on, you may have a faulty door switch. The door switch controls the interior lights and is activated whenever the door is tightly shut. So, if the refrigerator is reading the door as open when it is shut, it means the door switch is not making contact with the electrical connections. Consequently, the control board cannot read it.
Tape the switch down and close the door. If the problem is with the switch, the door open light should go off. And if this happens, you may have to replace the switch entirely or tape a small object on it to activate it correctly whenever you close the door. Get a technician to replace the switch or troubleshoot to find other possible causes if the problem persists after taking these steps.
KitchenAid Refrigerator Not Making Ice, Red Light Blinking – Quick Fix
If you find the red status light on your KitchenAid ice maker blinking with no ice production, there may be an ice jam issue or a defective optics board. This article on a KitchenAid refrigerator ice maker not working and red light blinking explains steps to troubleshoot and fix the problem.
KitchenAid Refrigerator Temperature Flashing – Fixed
You must check the internal temperature if the Over Temp light is flashing on your KitchenAid refrigerator. If the freezer temperature rises beyond 15 degrees Fahrenheit and the refrigerator rises above 48 degrees Fahrenheit, the Over Temp alarm goes off, and the light flashes. Ensure the door shuts and seals properly; you may want to test the door gasket.
Also, ensure the temperature setting is correct. Incorrect settings can trigger the alarm and cause the light to flash. Adjust the setting for the refrigerator or freezer if the setting is incorrect. This may fix the temperature problem after a few hours. Check the cooling function to ensure it is operating if it is in order. Otherwise, the refrigerator stops cooling, and the Over Temp light flashes.
Follow the instructions in the user manual to turn on the cooling function in the refrigerator if it is off. Afterward, give the refrigerator time to cool to stop the flashing temperature light. However, reset the refrigerator if the light keeps flashing after trying these steps. Turn off the circuit breaker for about five minutes to cut the power off to the refrigerator.
Next, turn it back on and ensure the cooling function is running. Then, monitor the appliance for some time to determine whether or not the temperature cools, and the light stops flashing. Your refrigerator may need servicing if the flashing continues. It may come from the control board, which governs all the refrigerator’s functions.
Important Note
A new KitchenAid refrigerator installation may take some time to cool, which may trigger the Over Temp alarm and light. The alarm and light will go off every 90 minutes until the internal temperature drops below 48 degrees Fahrenheit in the refrigerator and 15 degrees Fahrenheit in the freezer.
However, it may take longer than usual if there is a power interruption, you load the refrigerator, or you open the doors too often before it has had time to cool. Therefore, allow the refrigerator to cool without opening the door or loading it. It is best to allow it to run for about 6 to 12 hours before putting anything in it.
How to Replace a KitchenAid Refrigerator LED Light
Each KitchenAid refrigerator model may have various instructions on replacing the LED light, depending on the location. So, you may want to consult the user manual for specific replacement instructions. However, if your model has the light on the side liner, look closely at the light; you will see a small dot. Now, disconnect the refrigerator from electric power before removing the LED light. Insert a putty knife on the side with the dot and pry the light loose from the refrigerator.
Next, gently remove the light from the housing because there is a wire connection behind it. Unlock the locking tab on the wire harness and separate the old LED light from the refrigerator. Get the new light and check the wire connection point, comparing it to the one attached to the refrigerator. Sometimes, the connection points are different, making it slightly difficult to connect the new one to the refrigerator.
So, if the connection point for the new LED light matches the wire harness in the refrigerator, all you have to do is to connect the light. Hold down the locking tab and make the connection. Release the tab and lock the light in place. Next, position it on the light housing on the side liner and gently snap it back into place. Close the refrigerator door, reconnect it to electric power, and test the new light.
However, if the connection points are not the same, you must remove the point from the old light that matches the harness in the refrigerator and connect it to the new light. That means using a pair of pliers to cut the wire from the new light close to the harness point. Discard the connection point and peel a small part of the red and black wires on the new light to make the connection easy.
Get the old LED light and cut the connection point, but do it closer to the light than the harness at the end because you will no longer need the light. Next, discard the old light and peel the wires on the harness to match that on the new light. The new LED light should come with separate connectors to enable you to connect the wires from the harness to the light; you must wrap the naked wires together as a raw connection without these connectors.
Ensure you maintain the polarity when making the connection; the black wires must fit each other, and the red ones to each other. Get one of the connectors and slide the two black wires into the twin holes on it. Tighten the connection by pressing the bar on the connector with the pliers to ensure the wires do not slide out. Do the same for the red wires using the second connector.
Now, take the new light with the connections to the refrigerator and position it on the hole. Connect the wire harness to the refrigerator and push the connectors into the hole, out of the way. Align the light and push it into place with no side hanging loose. Reconnect the refrigerator to electric power and test the light. Ensure the cooling function is on in the appliance.
KitchenAid Refrigerator Indicator Light Comes On But Turns Off – Quick Fix
A KitchenAid refrigerator has several indicators serving different purposes. If the Cooling Off indicator comes on and turns off, checking the cooling function in the refrigerator is crucial. Monitor the light and follow the instruction in the user manual to turn it off and on again. Give it a few minutes, and if it continues to come on and go off, there may be a problem with the control board.
A faulty control board may also affect the water filter or air filter indicator where applicable. But before deciding on that, check the water filter to ensure it is not due for a replacement. It should be replaced every four to six months, depending on usage. Depending on usage, the air filter must be replaced every three to six months. If the air or water filter is old, it may trigger the indicator to turn on and off. Eventually, the indicator may remain on as it alerts you to replace the water or air filter.
However, if none of the above applies, reset the refrigerator to allow the control board to reboot. Disconnect the appliance from electric power for about two to five minutes. During this time, do not open the refrigerator door. Afterward, reconnect the appliance to electric power and wait a few minutes to ensure the cooling function is running. If the indicator continues to come on and turn off, hire an appliance technician to check the main control board. It may have loose connections or burnt relays.
KitchenAid Refrigerator Keeps Beeping, Flashing, and Powering Off
The refrigerator may have a temperature issue if it keeps beeping and flashing. Check the internal temperature to ensure it is correct. Different issues, such as dirty coils or a leaky gasket, can cause the temperature to rise. The same applies if you frequently open the door, hold it open for too long, or fail ot close it properly.
There is also the possibility that a recent power outage has caused the temperature to rise or the control board is faulty. This article on a KitchenAid refrigerator beeping, flashing, and powering off offers some instructions on fixing the problems. You may also contact the KitchenAid Service Center to report the issue and request service. Alternatively, employ the services of an independent technician for further assistance.
KitchenAid Refrigerator Ice Maker Troubleshooting – Red Light Off
Ensure the ice maker is on if you find the red light off. The red light is a status light that informs you of the ice maker’s functionality. It should be on and steady; if it starts blinking, it indicates a problem with the machine. Check to see if the ice maker has a dedicated power button; turn it off and on to ensure the ice maker is running.
Next, check the red light; if it remains off while the ice maker is on, it may be a problem with the ice maker assembly or the control board. Allow the ice maker to run to see if it produces ice. If nothing happens, you may have to replace the ice maker or have an experienced technician check the assembly and control board for possible repairs before replacing any part.
KitchenAid Refrigerator Light Won’t Turn Off – How to Fix
If you find that the light in your KitchenAid refrigerator will not turn off, it may indicate that the door or light switch is faulty. It may also indicate the light socket has malfunctioned. Before removing any part, turn the light bulb in the socket and see if there is any response. If none, press the light switch.
The switch’s location depends on the KitchenAid refrigerator model, but it is usually on the side liner or on top of the freezer door. The light should respond if the switch is in good working condition. Otherwise, check to see if the switch sticks; over time, moisture can affect the switch, or calcium may build on it. As a result, it stops working, even if the wiring is correct. Cleaning the switch with warm water and mild soap can fix the stickiness.
But if it is not sticky or there is no calcium buildup, you may have to replace the switch. Get a multimeter and run a continuity test on it. Then, you can be sure that you need a new light or door switch if there is no continuity. Replacing the switch is usually easy; pry the switch loose from the socket using a putty knife or a small screwdriver.
You may need to apply a piece of painter’s tape next to the switch before prying it loose to avoid scratching the refrigerator. Ensure you disconnect the refrigerator from the electric power before removing the switch. You will find wires connected to it using a harness once you loosen it; disconnect the harness and connect it to the new switch.
Push the switch into the socket, reconnect the refrigerator to electric power, and test the switch. Another possibility is that the light socket is faulty. So, if the light switch is in order, but the light remains on, replace the socket.
Important Notes
You can opt to take the refrigerator’s light bulb out if the above steps are beyond your skills and you do not want to use an appliance technician. The only job of a refrigerator light bulb is to illuminate the appliance’s interior, especially when there is no natural light. So, taking the bulb out does not damage any appliance part; you can leave it out until you find a permanent solution.
You will know that the refrigerator light does not turn off if the food items closest to it do not cool or becomes warm. Also, pressing the light switch should turn the light on or off. No response to pressing the switch indicates a fault. Finally, the light board may be faulty, but a technician should check this part because it is common to misdiagnose control boards.
How to Turn Off the Dispenser Light On a KitchenAid Refrigerator
Try resetting the refrigerator by disconnecting it from the electric power. Do this by unplugging it from the power outlet or turning off the circuit breaker. Leave the appliance off for about five minutes and turn it on again. That should reset the dispenser light and turn it off.
But if that does not work, check the water dispenser switch. There may be a dedicated switch that controls the dispenser; on models with an ice dispenser, there should be two switches. Each switch controls each dispenser, and if any of the switches is stuck, the dispenser light does not go off.
The switch may appear as a button marked with a small light bulb icon on the control panel. Press the icon and see if the light turns off. If it remains on, there may be a problem with the dispenser control board, and an appliance technician should check and fix the refrigerator.
KitchenAid Refrigerator Display Panel Won’t Light Up – Fixed
Check to see if the Control Lock function is active. The lock function disables all the dispenser buttons and lights to prevent accidental discharge with children or when cleaning the refrigerator. Most models with this feature should have a Lock icon on the control panel, illuminated when active. Locate the lock button and press it to turn off the lock feature; you may want to check the user manual for instructions on the lock feature.
Otherwise, reset the refrigerator; disconnect it from electric power for five to ten minutes, and reconnect to power. Ensure the cooling function is running and check the display panel. If the problem continues, report the issue to the KitchenAid Service Center or hire an independent technician for further assistance.
Will My Ice Maker Stop Working If the Water Filter Light Is On?
Your ice maker will still work if the water filter light is on as long as the water supply from the main source is steady. The water filter removes the impurities from the water flowing into the refrigerator so that you have clean water from the dispenser and clean ice from the ice maker. However, the filter becomes clogged with contaminants over time, especially where the refrigerator water is constantly used.
So, replace the filter every four to six months, especially when you see the ‘replace filter’ light. However, the ice maker will keep working whether or not the filter light is on, but it is best to replace the filter once the light begins flashing. Otherwise, the water supply to the refrigerator will eventually become restricted because of the clogged filter or stop working altogether.
KitchenAid Refrigerator Red Cooling Off Light On When Door Is Open – Quick Fix
It means the cooling function in the refrigerator is off if the red light is on whenever you open the door. You may have inadvertently turned it off, or there is an internal issue with the refrigerator. First, check for the Cooling Off icon on the control panel; if it is lit, the function is off, and the refrigerator will not cool. And if that applies, consult the user manual for steps to activate the function. If the cooling function does not work, the refrigerator needs servicing; have a service technician check and fix it.
KitchenAid Refrigerator Water Light Won’t Turn Off – What to Do
Ensure you follow the specific instructions for resetting the filter light for your refrigerator’s specific model. Each model has specific instructions for resetting the light, and you should follow them once you replace the filter. Some models have a dedicated filter reset or water filter button; press and hold it for three seconds to reset the status light. Otherwise, there are other button combinations that work if the refrigerator does not have these buttons, as discussed earlier in this article.
Also, ensure you use the right filter type and correctly install it. Using the wrong filter type for a KitchenAid refrigerator may keep it from working, which keeps the filter light from resetting. Always use an Everydrop or Whirlpool water filter for your refrigerator, and ensure you install it properly if it is to work. You may find water leaking from the filter if it is incorrectly installed. However, your refrigerator may need servicing if the light will not reset. Therefore, request assistance from an appliance technician to fix the issue.
KitchenAid Refrigerator Leaking Water Inside from Light – Solved
If you find water leaking around the light inside your KitchenAid refrigerator, you may want to check the filter, filter housing, or water line. The filter may be damaged or have a tiny hole through which water leaks. Remove the filter and inspect it; if there is any damage, you must replace it.
The same applies to the filter housing; cracks in the housing cause leaks inside the refrigerator. In addition, check the water line that connects directly to the water filter from the source. Replace it if there is any sign of damage. You may need a service technician to troubleshoot further and fix possible causes of the leakage.
Get Instant Help — Ask An Experienced Verified Appliance Technician
Need expert help? Click here to use the chat box on this page to speak with a verified appliance technician right away. No need for expensive in-home service calls. No appointments. No waiting.