There are benefits to using a Norcold refrigerator. But the joy of those benefits can be stifled if error codes appear and you don’t know what to do. So read this article to solve Norcold refrigerator error codes and messages.
Table of Contents
Norcold Refrigerator Error Codes and Messages – N62X Model
This error code indicates that the door of the refrigerator has been open for longer than 2 minutes. To fix the code, simply shut the door of the refrigerator properly.
When there is no display on the refrigerator’s control panel, it means there is no power supply to the refrigerator.
Check to be sure that the power cord is still working and is plugged in fully if it is. Also, check the circuit breaker for that part of the house.
When you see this error code, be sure that the refrigerator’s manual shut-off valve is open.
This code means that the refrigerator’s control panel is not receiving AC voltage. Check the wall outlet to be sure it is working.
When you see this error code, then know that the supply of DC voltage to the control panel of the refrigerator is quite low. Contact a qualified technician to verify the fault and fix it.
S, H, r
Any of these error codes indicate that there is a fault in the controls of the refrigerator. Call a professional refrigerator service agent to take a look and fix it.
Norcold Refrigerator Error Codes and Messages – 1210 Model
dr with an Audible Alarm
This error message indicates that the door of the refrigerator has been open for longer than 2 minutes. Shut the door properly to fix it.
no, FL with Audible Alarm
The code indicates that the burner didn’t ignite at all or didn’t ignite again. Check to ensure that the refrigerator’s manual shut-off valve is open. Also, be sure that the propane gas tank valve is open and that the gas has the right pressure. Additionally, ensure that the gas supply line has no air in it.
rE or AC with Audible Alarm
There is something wrong with the refrigerator controls if you see this error code displayed. Contact the Norcold service center or call a qualified technician to fix the fault.
no, AC with Audible Alarm
This error code signifies that there is no AC voltage available to the control panel of the refrigerator.
Be sure that the wall socket where the refrigerator is plugged in is in the correct working order. Then, check the power cord of the refrigerator for damage. Furthermore, you can check the circuit breaker or the fuse to be sure it is working fine.
Sr or HE
When you see this error code displayed, you know there is a problem with the refrigerator’s controls. You should call a qualified technician to fix it or contact the Norcold Service Center for further assistance.
Temperature Setting Flashing
If you press the Set Temp key and the refrigerator’s temperature keeps flashing on the control panel display, then know that the refrigerator is using the Back Up Operating System to work. You need the services of a technician. Contact Norcold or any other trusted refrigerator technician.
dc or LO
The DC voltage supply to the refrigerator’s control panel is too low if you see this error code displayed. Ensure that the equipment for charging the battery is functioning as it should.
L1 or oP
The limit switch that controls the high temperature in the refrigerator is open. Call a refrigerator technician or the Norcold service center to fix it.
But if you have to fix it yourself, here is a video to guide you…
Check out these other related articles…
- Thermador Refrigerator Error [Solved]
- Midea Refrigerator Error [Quick Fix]
- Samsung Refrigerator Error [How to Fix]
- Whirlpool Refrigerator Error [Solved]
- LG Refrigerator Error [How to Fix]
- Maytag Refrigerator Error [Solution]
no, AC with Audible Alarm
If you see this error message displayed, there is no available AC voltage supply to the refrigerator control. Contact the Norcold customer care center or a qualified technician to fix this error.
This error code means that there is no available DC voltage supply to the refrigerator’s control panel. It could also mean that the refrigerator is off.
Check to ensure that the refrigerator’s power cord is not burnt or damaged. Then, plug it properly into a working wall socket.
Also, check to ensure the AC/DC converter is working fine. Additionally, ensure that the equipment that charges the battery is working fine.
If you cannot check all these yourself, call a service agent.
Norcold Refrigerator Error Messages – N3104 Model
Refrigerator Senses Flame
The gas valve is defective when the unit senses flame even though the gas mode has not been selected.
No Ignition of Flame
If the flame doesn’t ignite after 30 seconds, then check for a bad electrode, faulty LCD display or control board, or a defective orifice or burner. You can also check if the gas tank is empty or if there is an obstruction to the gas flow.
DC Heater Turned Off
If you find that the DC heater is off when it should be on, check the heater; it could be defective. Also, check the LCD display or the control board for faults. Additionally, the fuse could be bad.
And if the heater indicates that it is on when it should be off, check the LCD display or the control board.
The module for controlling the burner could sense wrong feedback from the refrigerator. If this happens, inspect the LCD display, the control board, or the burner itself.
No Engine Running
If you see this error message displayed, then know that the refrigerator is in manual DC mode. Check the LCD display, the DC input source, or the control board.
AC Heater On
When the Ac heater is on, even though it should be off, either the LCD display is malfunctioning or the control board is defective.
AC Heating Element
If the AC heating element fails, check to see if the DC heater has failed, too. This could trigger the failure of the AC heater. Also, check the fuse, the AC input source, the LCD display, and the control board.
Failure of Thermistor
Check the connections of the thermistor wires to see if they are loose or improperly connected. Then, check the thermistor itself. Check the LCD display or the control board if the above are in working order.
In addition to the above, if the refrigerator doesn’t start, check the DC input source or the control board. Furthermore, check the communication cable if there is a loss in communication between the LCD display and the control board. You can also check the display panel and the control board to see if they are damaged.
Most of the faults listed above will require the services of a Norcold service agent or any other qualified technician. This is due to the technicality involved in fixing them. Besides, it is safer to tow this route; the chances of failure are very slim.
Other Error Codes in a Norcold Refrigerator
This error code informs you that the refrigerator has not produced any refrigerant for about 2 hours. This means that the boiler of the refrigerator is getting too hot.
This is a profoundly serious problem that needs immediate attention. So contact the Norcold customer service center to request service or call a trusted and qualified technician.
This means that there is a communication error between the display panel inside, from where you turn the unit on, and the lower circuit board. It may be a connection issue, so check the wires and other connections on the control board.
Contact a qualified RV refrigerator technician or the Norcold customer service center to request a service agent if you have difficulty checking or fixing the issue.
Norcold Refrigerator Error Code E3
If you see this error code, the DC voltage that powers the refrigerator is out of range. That means that the voltage is too high or too low, causing the refrigerator to have power issues. DC voltage is what powers the appliances in your RV, even if you are connected to AC power outside.
Your inverter converts the power to DC so you can use it for your camper. Ensure the battery produces 12.2 volts; if not, it may be a problem with the battery or a defective refrigerator component. Have a technician troubleshoot further to determine the source of the problem and recommend a permanent fix.
Norcold N3150 Fridge Error Code 9
It is not common to see this error code because it means the DC voltage to the fridge is too high. Check the battery or power connection if the fridge is connected to electric power.
However, it may be a problem with the power converter, which provides too much voltage to the fridge. Have a service technician take a look at the power connection or check the service manual to ensure you have the correct error code and determine how to fix it.
Need expert help? Click here to use the chat box on this page to immediately speak with a verified appliance technician. No need for expensive in-home service calls. No appointments. No waiting.