Like most refrigerators, a Kenmore refrigerator control governs most refrigerator functions. But if there are problems, the refrigerator won’t work as it should.
Table of Contents
Where Is the Damper Control on a Kenmore Refrigerator?
The damper control is located between the freezer and the refrigerator. Typically, it is at the top back panel, close to the top.
Kenmore Refrigerator Control Board Reset
To reset the control board on a Kenmore refrigerator, open one of the refrigerator’s doors. Press the Home and Ultra Ice buttons at the same time. Hold them for about five seconds to turn the controls off.
Next, disconnect the refrigerator from electric power and reconnect it again. Going through this process resets the refrigerator’s control board.
Kenmore Refrigerator Control Board Replacement
To replace the control board on a Kenmore refrigerator, take the following steps:
Step 1
Disconnect the refrigerator from electric power or shut off the circuit breaker. You don’t have to remove any frozen foods because the unit won’t stay off for more than an hour.
But if you would rather keep the food in a cold environment, find another refrigerator or an ice-packed cooler. Afterward, pull the unit away from the wall behind to create access to the control board.
Step 2
There is a cover over the control board. The board may be in the ceiling or a side wall inside the uni for some models.
When you find the board using the user manual, unthread the screws holding the cover in place over it. Then, set it aside.
Step 3
Take photos of the wire connections before disconnecting any of them. Then, disconnect them; how you disconnect the wires will depend on the type of Kenmore refrigerator you own. You may have to release a tab or pry the connectors off.
Step 4
You will find locking tabs on the sides of the control board. Release the tabs so you can pull off the old control board.
Put the new control board in the place of the old one and start reconnecting the wires. It is at this point that you are going to need the photos of the connections you took earlier.
Reduce static discharge by wearing a ground strap or touching the metal cabinet. Otherwise, the discharge may destroy the new board.
Replace the cover of the control board, making sure to set the screws in place and tighten them securely. Then, reconnect the refrigerator to electric power.
Note: These steps apply to side-by-side, bottom freezer, and top-freezer Kenmore refrigerators.
Here is a video showing how to replace the control board on a Kenmore refrigerator…
Kenmore Elite Refrigerator Control Panel Reset
To reset the control panel on a Kenmore Elite refrigerator, disconnect the refrigerator from electric power. Give a space of about a minute before plugging it back into power. If the control panel does not reset, use the Lock key.
Find and press the key on the panel for about 3 seconds. If the control panel is locked, the action unlocks it. Otherwise, there may be a connection fault within the panel. Find a qualified appliance technician to troubleshoot further.
If the control panel does not seem to be working, it might be locked. Therefore, use the Lock key to unlock it. But if the key does not work, your refrigerator needs servicing.
Kenmore Elite Refrigerator Control Panel Blinking – What to Do
Check for error codes on the control panel display. If there are codes, find the corresponding component failure that matches the code and fix it.
While checking the codes, check to see if the refrigerator is still cooling. If it is no longer cooling, the problem stems from the control board. Move the perishable food items to another refrigerator and replace the control board.
Kenmore Elite Refrigerator Control Board Green Light – What It Means
If you see a green light on the control board of your Kenmore Elite refrigerator, check the number of times it blinks. If it blinks more than once, it points to a fault with the board that supplies power to the compressor or the compressor itself. But before replacing any of these components, make sure the connection running between the compressor and the board is secure.
Kenmore Refrigerator Temperature Control Location
The location of a Kenmore refrigerator temperature control is on the back wall of the unit’s interior, right on the upper part.
Kenmore Refrigerator Ice Maker Control Light Blinking – Quick Fix
To determine why the control light is blinking on a Kenmore refrigerator ice maker, verify your model’s year of manufacture. There are different methods for troubleshooting and fixing the issue, as this article explains in detail.
Kenmore Refrigerator Temperature Control Not Working – Solved
Find the temperature control and turn the knob to the highest temperature setting. If the cold control clicks, it may not be defective. But if it does not click, check for continuity using a multimeter. If the meter shows no continuity from the cold control, no matter its temperature setting, replace the cold control.
This video shows how to replace the thermostat on a Kenmore refrigerator…
Check out these other articles…
Refrigerator Compressor Is Hot [Solutions]
Refrigerator Compressor Is Bad [How to Fix]
Refrigerator Compressor Leaking [How to Fix]
Refrigerator Compressor Burning Smell [Solutions]
Refrigerator Compressor Explosion [Critical Info]
Kenmore Refrigerator Control Panel Removal – Steps
To remove the control panel on a Kenmore refrigerator, first, disconnect the refrigerator from electric power. Then, inspect the panel for a notch for prying it loose. When you find it, insert a putty knife or a flat-head screwdriver in the gap and begin prying the panel off.
Gently work around the panel until all the sides are free. Then, you can pull it up and off the refrigerator.
How to Replace a Kenmore Refrigerator Dispenser Control Board
To replace the dispenser control board on a Kenmore refrigerator, take the following steps:
Step 1
Pull the power cord of the refrigerator from electric power or power down the breaker. Find suitable food storage for perishable food items before disconnecting the power.
Step 2
Pull the drip tray out from under the dispenser until it does not move anymore. Then, lift the back to unlock the tabs before sliding it entirely out.
Step 3
Unmount the screws you see at the dispenser housing’s back. After that, lift the top of the housing and pull its bottom towards you to remove it.
Step 4
Turn the dispenser housing over and pull out the wire harnesses at the back. Doing this frees the housing so that you can pull it out entirely.
Step 5
Lift the flap over the control board and hold it away from the board. Then, unlock the tabs and pull out the wire harnesses from the board. You may want to take photos of the connections for when you are installing the new board.
Set the new board in position and reconnect the wires. Consult the photos, so you don’t make a mistake. Afterward, reverse steps 5 to 1.
Recap
A Kenmore refrigerator control handles different functions, and there is more than one control. If there is a problem, it is crucial to find the source and fix it immediately. Contact Kenmore if you have any difficulty fixing the refrigerator control.
Get Instant Help — Ask An Experienced Verified Appliance Technician
Need expert help? Click here to use the chat box on this page to speak with a verified appliance technician right away. No need for expensive in-home service calls. No appointments. No waiting.