Frigidaire Refrigerator Dispenser Problems [Solved]

With this in-depth article, you can troubleshoot and fix your Frigidaire refrigerator dispenser problems without breaking a sweat.

Table of Contents

Frigidaire Refrigerator Water Dispenser Not Working – How to Fix

Troubleshoot the following parts of your Frigidaire refrigerator dispenser and fix the defective ones:

1. Water Tube

One of the reasons why a refrigerator water dispenser is not working is that the water tube is frozen. To know if that is the case with your appliance, start by unplugging it from the power source. Next, detach the water tube from the refrigerator and use a hairdryer or leaf blower to circulate air through it.

A frozen water tube will prevent the circulation of air, so melt the ice. Also, make sure that the freezer temperature is between 0 and 10 Fahrenheit. The reason for this is to prevent the freezer from getting too cold or warm.

2. Water Inlet Valve

As the water inlet valve opens, water flows to the dispenser at a pressure of 20psi. However, this process will not take place if the water pressure is below 20psi, and if the water inlet valve is broken.

In light of the above, troubleshoot the water inlet valve by running a continuity test using a multimeter. If there is continuity in the water inlet valve, then move on to troubleshoot the next component. However, if the multimeter reading shows that there is no continuity, replace the water inlet valve.

3. Dispenser Control Board

The dispenser control board is the heart of the dispenser system. If it is faulty, all other components will not work. But thankfully, the dispenser control board rarely gets broken, so you may troubleshoot other components before coming to it.

If you discover that the dispenser control board of your Frigidaire refrigerator is bad, do not attempt to repair it. Instead, go for a new one, even though it is more expensive. In the long run, you will realize that is a cost-effective investment.

4. Dispenser Switch

The Frigidaire refrigerator dispenser comes with several switches that facilitate the flow of voltage to the dispenser. If just one switch is burnt or cuts, the dispenser will stop working.

Apart from physical inspection, you can conduct a continuity test to know the working condition of the dispenser switches. If the multimeter reading indicates that there is no continuity, replace the dispenser switches.

5. Water Filter

The water filter of your refrigerator dispenser system ensures that you only get pure water in your cup. It traps dirt on its pores and over time the pores get clogged. When this happens, the dispenser will not work.

To prevent the water filter of your Frigidaire refrigerator from getting clogged, replace it at least twice a year.

6. Door Switch

As you open the door of your Frigidaire refrigerator, the water dispenser turns off with the help of the door switch. If for some reason, the door switch goes bad, the water dispenser system will not work.

The only to truly know if the door switch is the source of the dispenser problem is to carry out a continuity test. If the test shows that the door switch lacks continuity, replace it.

[amalinkspro type=”showcase” asin=”B07K8DLQBD” apilink=”https://www.amazon.com/dp/B07K8DLQBD?tag=refrigeratorsreviewed-20&linkCode=osi&th=1&psc=1″ new-window=”true” addtocart=”true” nofollow=”true” sc-id=”6″ imgs=”LargeImage” link-imgs=”false” specs=”Production Name: Generic Refrigerator Door Light Switch, Module Type: HCK-50, Rated Voltage: 125/250V AC, Rated Current: 2.5A 250V/5.0A 125V, Work Temperature: -40℃-85℃/-40℉-185℉,Control Type: NC(normally close, most refrigerator control type),Connect Pin Size: 4.8×0.5mm/0.19×0.02in” btn-color=”#ff9900″ btn-text=”Buy on Amazon” alignment=”aligncenter” hide-prime=”0″ hide-image=”0″ hide-price=”0″ hide-button=”0″ width=”600″]Generic Refrigerator Door Light Switch 2 Feet Compatible for GE Whirlpool, Maytag, Admiral, Amana, Crosley, Jenn-Air, Kenmore, KitchenAid, Magic Chef 2 PCS[/amalinkspro]

Frigidaire Refrigerator Ice Dispenser Not Working – What to Do

If your Frigidaire refrigerator ice dispenser is not working, troubleshoot the following parts and replace anyone found to be defective:

1. Dispenser Control Board

The ice dispenser system is controlled by the dispenser control board. Hence, if it packs up, the entire dispenser will not receive power.

Run a continuity test with the help of a multimeter to know whether the dispenser control board is broken or not. It is best to get a new dispenser control board than to repair a defective one, which will break down again in no time.

2. Dispenser Switch

If any of the door switches of your ice dispenser is burnt or cut, the ice dispenser will not function. In addition to doing a physical inspection of the dispenser switches, run a continuity test to be doubly sure the ice dispenser problem is emanating from the switches. If the test indicates that the dispenser switch is bad, get a new one.

3. Dispenser Actuator

The dispenser actuator and the dispenser switch of your ice dispenser help to power the auger motor. Without the dispenser actuator, the dispenser switch will not work. In light of this, conduct a continuity test using a multimeter to determine the working condition of the dispenser actuator. Replace the dispenser actuator if the test shows it is not working.

4. Auger Motor

If the auger motor is broken, the auger blade will not rotate and if it does not rotate, there will be nothing to push the ice through the chute of your dispenser.

Take out the ice bucket and rotate the auger blade by hand. If you feel a slight resistance in the rotation of the auger blade, it means the auger motor needs to be replaced.

5. Dispenser Solenoid

The door flap that opens for ice to go through the chute is powered by the dispenser solenoid. So, having a defective dispenser solenoid, means you won’t get ice when you want it.

There are two ways to determine whether the dispenser solenoid is defective or not: continuity test and hand rotation. The former involves using a multimeter to test for continuity, while the latter involves rotating the actuator pin of the solenoid to see if it rotates freely. If the solenoid does not rotate freely and if the test reading shows the solenoid lacks continuity, replace it.

6. Ice Bucket Auger

As the dispenser lever is pressed down, the dispenser door opens for ice to go down the chute and into your glass. The ice bucket serves as storage for the ice and the auger rotation facilitates ice movement to the chute.

If the ice bucket auger is broken, or if the auger motor is disconnected, the ice dispenser will stop working. A broken ice bucket lever has to be replaced before you can start dispensing ice again.

Frigidaire Refrigerator Water Dispenser Lever Broken – Fast Fix

To begin with, if the lever of your Frigidaire refrigerator water dispenser is broken, water will not come out from the chute. To fix the broken lever, you need a multi screwdriver and a putty knife. Follow the step below to fix the lever of your refrigerator dispenser:

First off, unplug your Frigidaire refrigerator and remove the drip tray from the freezer section. Next, bring down the façade by inserting your putty knife at the bottom. Before disconnecting the dispenser switches, take note of their arrangement because you will have to rewire them after fixing the lever.

The next step is to take out the dispenser light bulb and its switch. Once that is done, detach the delay mechanism and pull out the defective lever after opening the chute door. Place the new lever in the position of the old one and insert the screws to secure it.

Now, reattach the delay mechanism to the door and screw it back up. After that, rewire the dispenser switch and ensure that the top of the dispenser façade is properly aligned with the edge of the dispenser housing. Also, insert the drip tray and plug your refrigerator back into its power source. If you followed the instructions as spelled out, the new lever should be working properly.

[amalinkspro type=”showcase” asin=”B087XBP58N” apilink=”https://www.amazon.com/dp/B087XBP58N?tag=refrigeratorsreviewed-20&linkCode=osi&th=1&psc=1″ new-window=”true” addtocart=”true” nofollow=”true” sc-id=”6″ imgs=”LargeImage” link-imgs=”false” specs=”DA97-08519A Refrigerator Dispenser Lever Assembly Compatible with some Samsung Refrigerators” btn-color=”#ff9900″ btn-text=”Buy on Amazon” alignment=”aligncenter” hide-prime=”0″ hide-image=”0″ hide-price=”0″ hide-button=”0″ width=”600″]DA97-08519A Refrigerator Dispenser Lever Replacement Assembly compatible with Some Samsung Refrigerators[/amalinkspro]

Frigidaire Refrigerator Water Dispenser Turns on by Itself – Solution

If your Frigidaire refrigerator dispenser automatically turns ON and dispense water, it is an indication that the water valve is defective. You should get a new one to replace the defective part. But then, when getting a new water valve, note that the model number of the new one must match the old one. Otherwise, you will end up wasting money on something that will not work.

Why is my Frigidaire Refrigerator Water Dispenser Leaking?

If you notice that your Frigidaire refrigerator water dispenser is leaking, troubleshoot the following components and fix the defective ones:

1. Water Filter Head

If the water filter head is cracked, the dispenser will leak. So, ensure you carefully examine the water filter head and replace it if you notice any cracks.

2. Water Inlet Valve

If the water filter head is not damaged, inspect the water inlet valve. Perhaps it may be broken or loosely fitted, thereby allowing water to leak. If the latter is the case, tighten the valve. On the other hand, replace the water inlet valve if it is broken.

3. Water Tank Assembly

The water tank assembly may be the source of the leak. Note that it may be difficult for you to detect a leak from the water tank assembly, especially if the crack is small. So, take your time in inspecting every corner of the assembly. If you eventually find a leak, do not attempt to fix it with glue. This is because the glue is proven to not be effective in holding plastic parts together. Instead, get a new water tank assembly.

4. Drain Pan

The drain pan of your refrigerator dispenser serves as storage for the water that thaws in the evaporator coils. If the drain pan is broken or gets filled up, you will notice a leak. Replace the drain pan once you notice any cracks or empty it when it is filled.

5. Water Filter

The water filter may be responsible for the leaks of your refrigerator dispenser if it is not connected properly to the filter housing. If that is the case, tighten the water filter and the leaking problem will be solved.

Frigidaire Refrigerator Water Dispenser Very Slow – How to Fix

Perhaps your Frigidaire refrigerator water dispenser takes over 2 minutes to fill a glass, even when the dispenser seems to be working properly. Here is how you can correct that anomaly in less than 10 minutes:

1. Check the Water Line

Once you notice your refrigerator water dispenser takes ages to fill a glass, check the water line to make sure that nothing is obstructing water flow. It may be that the water line is leaking or twisted. Whichever the case, get a new water line for your Frigidaire refrigerator water dispenser and you should be able to fill your glass of about 8 ounces in less than 10 seconds.

2. Check the Power Supply

To begin with, if the voltage transmitted to the water dispenser is not high enough, the dispenser will not work optimally. One of the ways the dispenser may start acting out is by dispensing water slowly. Ensure that the power supply to the refrigerator is adequate and if the dispensing issue persists, follow the next instruction.

3. Inspect the Water Filter

The water filter is installed in the dispenser to make sure that the water you get to drink is free from impurities. The dirt in the water is trapped by the water filter and over time, the pores will be clogged with dirt.

When this happens, it is either the water dispenser does not dispense water at all or it does so slowly. Check if the water filter is clogged and replace it if it is.

[amalinkspro type=”showcase” asin=”B002JAKRAM” apilink=”https://www.amazon.com/dp/B002JAKRAM?tag=refrigeratorsreviewed-20&linkCode=osi&th=1&psc=1″ new-window=”true” addtocart=”true” nofollow=”true” sc-id=”6″ imgs=”LargeImage” link-imgs=”false” specs=”Enjoy fresh tasting water right from the fridge and directly in your glass with the Pure Source Ultra water filter. Designed to remove harmful contaminants giving you peace of mind with every glass” btn-color=”#ff9900″ btn-text=”Buy on Amazon” alignment=”aligncenter” hide-prime=”0″ hide-image=”0″ hide-price=”0″ hide-button=”0″ width=”600″]Frigidaire ULTRAWF Pure Source Ultra Water Filter, Original, White, 1 Count[/amalinkspro]

Frigidaire Refrigerator Dispenser Light Stays On – What to Do

If your Frigidaire refrigerator dispenser light refuses to turn off, do the following:

Troubleshoot the Light Switch

When troubleshooting the light switch of your refrigerator dispenser, observe closely if it has some stickiness or resistance. If it does, it means there is a buildup of calcium in the light switch panel. You can clean the panel to get rid of the stickiness. Once that is done, check if the light problem persists. If it does you should replace the light switch.

In addition, replacing the light switch is not all that difficult. Remove the old light switch using a butter knife or screwdriver. You will see two wires in the switch compartment, remove them gently. Now, insert the new light switch and rewire it properly.

Inspect the Bulb Socket

If everything about the light switch checks out, then check the light bulb socket. You can open the socket the same way the light switch was opened. If the connection is not intact, then the light bulb socket might be responsible for the lighting problem. If you cannot repair the light bulb socket, go for a replacement.

Reset the Dispenser System

If the components mentioned above are not responsible for the lighting problem, the power supply to the refrigerator needs to be turned off and put back on after five minutes. This simple action will reset the dispenser system and the light will most likely start working properly. However, if that is not the case, call a professional to help you do a thorough inspection. Check out the video below to learn more about resetting your Frigidaire refrigerator dispenser…

Check out these other related articles…

Frigidaire Refrigerator Dispenser Lock Out – Fast Fix

To begin with, note that the lock mode can help prevent the unwanted opening of your refrigerator dispenser. However, the lock mode sometimes activates itself, making it frustrating when you want to use the dispenser. To activate or deactivate the lock mode, press the Control Lock button, which can be found next to the Light button. Note that you are to press and hold down the Control Lock button for about three seconds, whether you want to activate or deactivate it.

Frigidaire Refrigerator Water Dispenser Stuck – How to Fix

If your Frigidaire refrigerator water dispenser gets stuck, it is an indication that the dispenser chute is clogged. Check if there is anything obstructing the flow of water in the chute and remove it. If the chute is twisted, consider replacing it.

Frigidaire Refrigerator Dispenser Problems – Related FAQs

How to Remove Ice Dispenser Cover on a Frigidaire Refrigerator

The ice dispenser cover conceals the internal components that facilitate the operation of the dispenser system. If any of the components is defective, you will need to remove the cover. Here is how to go about it:

Go to the right or left side of the plastic trim and take out the slot using a butter knife or screwdriver. Next, pry the edge of the plastic trim from the refrigerator. When doing this, you have to be very careful not to damage the plastic trim.

After that, take out the cables wired to the control panel and you can have access to the internal components of the ice dispenser.

How Do I Clean My Frigidaire Refrigerator Water Dispenser?

To clean your Frigidaire refrigerator water dispenser, disconnect the water tank and flush it with distilled vinegar. Do not use bleach in place of the distilled vinegar because it is too harsh and may damage the aluminum coating of the refrigerator.

Now, scrub the nozzle of the water dispenser to get rid of the bacteria residue. After that, rinse the vinegar so that it does not contaminate your water. Finally, clean the exterior of the refrigerator dispenser.

How Do I Remove the Ice Dispenser from My Frigidaire Refrigerator?

To remove the ice dispenser on your Frigidaire refrigerator, unplug it and open the unit to access the ice bucket. Unscrew the two 1/4-inch hex-head bolts holding the ice maker in place. Next, use your fingers to press down the locking tabs on both ends of the wiring harness.

You can now perform whatever repairs or replacement you need to do on your ice dispenser. Once you are done, use your electric tape to wrap the wiring harness to the wall of your refrigerator and fasten every screw you removed initially. Now you can plug your refrigerator back into the power source.

Get Instant Help — Ask An Experienced Verified Appliance Technician

Need expert help? Click here to use the chat box on this page to speak with a verified appliance technician right away. No need for expensive in-home service calls. No appointments. No waiting.