Electrolux Refrigerator Dispenser Problems [Solutions]

Is your Electrolux refrigerator water dispenser not working or is it leaking? This article covers how you can troubleshoot your Electrolux refrigerator water dispenser problems and fix them all by yourself.

Table of Contents

Electrolux Refrigerator Water Dispenser Not Working – Solutions

If your Electrolux water dispenser is not working, troubleshoot the following components:

1. Water Supply Tube

If the water supply tube of your dispenser is frozen, detach the tube from the door and use a blower to circulate air through it. Have it in mind that the water supply tube is frozen if there is no circulation of air through the tube.

Now that you know the water supply tube is frozen, melt it using the blower or just allow it to sit outside the dispenser for some time. When troubleshooting, make sure the freezer temperature is at an optimal setting. That means the temperature has to be around 0 to 10 degrees Fahrenheit. The water tube of the dispenser may freeze again if the freezer temperature is too cold or too warm.

2. Water Inlet Valve

This component of your Electrolux refrigerator water dispenser facilitates water supply. If the pressure of the water inlet valve is quite low or if it is faulty, the valve cannot be opened. To be specific, the water inlet valve pressure should not be less than 20PSI for it to work.

To know if the water inlet valve is faulty, test it for continuity using a multimeter. If there is no continuity in the water inlet valve, you have to go for a replacement.

3. Dispenser Control Board

Without the dispenser control board, the water dispenser will be as good as useless. That is because there will be no power supply to the dispenser system. Perhaps only one part of the dispenser is not functioning, conduct a continuity test to if that part is actually defective. If it is, then replace that part.

Similarly, if the entire dispenser control board is malfunctioning, replace it and your dispenser system will start working.

4. Dispenser Switch

The function of the dispenser switch is to transfer the voltage that powers the dispenser. The dispenser comes with several switches and if any is broken, best to believe the dispenser will not function.

To determine if a dispenser switch is faulty, you need to do a continuity test. The test will help you in deciding if you should go for a dispenser switch replacement.

5. Water Filter

The water filter ensures that you always get clean and clear water at all times. If the water filter of your Electrolux dispenser is clogged, there will not be any flow of water and that makes the dispenser useless.

Refrigerator dispenser manufacturers recommend that you replace your water filter once or twice a year to ensure it is not clogged over time.

Now, let’s go to another Electrolux refrigerator dispenser problem…

What to Do If My Electrolux Refrigerator Water Dispenser is Slow?

To start with, you will know if your water dispenser is slow if it takes more than eight seconds to fill a glass of eight ounces.

If your Electrolux refrigerator water dispenser is too slow, start your troubleshooting with the water tank. If the water tank is not full, supplying water to the dispenser may become slow. That is because it will not have the required pressure to flow to the dispenser.

To ensure the water tank is filled to its capacity, hold down the water dispenser for about three minutes, so the tank can be filled.

Apart from the water tank, troubleshoot the water valve or saddle valve, especially if the dispensing problem started recently. If the valve is having an obstruction, there will not be a free flow of water to the Electrolux dispenser.

Do not also rule out the possibility of the water line is frozen, kinked or bent. If that is the case, the free flow of water will be impeded.

Another thing to consider is that the water filter is clogged. If that is the case, water will dispense very slowly. Refrigerator experts advise that you change your water filter at least twice a year.

The dispenser switch may be defective if you hear a clicking or humming sound, while water is not being dispensed. The manufacturer’s guide of the Electrolux refrigerator water dispenser shows you actionable steps to troubleshoot the dispenser switch.

We must quickly state in clear terms that you need to turn OFF and unplug your Electrolux refrigerator water dispenser before attempting to troubleshoot any component. Check out the video below to learn more about fixing a water dispenser that is too slow…

Check out these other articles…

Electrolux Refrigerator Water Dispenser Leaking – How to Fix It

Your Electrolux refrigerator water dispenser may start leaking depending on how you maintain it. The truth is nobody wants warped wooden floors, which can be slippery. So, here are components of Electrolux dispenser that you should troubleshoot if you have a leaking appliance:

1. Vinyl Tubing

If the vinyl tubing, which links the dispenser to the water supply source, tears or splits, the tubing will start leaking. But then, you do not have to panic because fixing it is quite easy. Start by taking off the old vinyl tubing before replacing it with a brand new one.

2. Water Line

Apart from the vinyl tubing, check the water line to see if it is dripping. If it is, perhaps the air is locked in the waterline, which causes accumulation of pressure. It is this accumulated pressure that causes water to leak from the dispenser.

To fix the defective water line, place a cup under your dispenser. Now, turn the knob to pour water in the cup until it is full. Continue doing this for about 5 minutes and at the end you would have succeeded in giving off all the trapped air in the waterline.

3. Water Valve

If water drips from the dispenser, another component to troubleshoot is the water valve. Sometimes, the water pressure might be too high and so water will escape from the dispenser even though it is not toggled ON.

Perhaps the problem may be that the water valve is just worn out and has nothing to do with the pressure. In this case, you have to get a new water valve. Also, it would be better to hire a technician than trying to fiddle with valves.

4. Catch Pan

The catch pan is a grate that stores the excess water dripping from the dispenser. When you take out your cup from the dispenser in one fell swoop after it is filled, or if there is no cup when the knob is turned on, the catch pan ensures that water does not spill all over the floor.

But then, when the catch pan is damaged, you will notice that water spills all over your floor, even when the pan is filled. This is not a dispenser issue but a catch pan defect. You have to get a new catch pan to prevent further spills.

Electrolux Refrigerator Ice Dispenser Not Working – Quick Fix

If the water section of your Electrolux dispenser is working properly but the ice section is not, troubleshoot the following components:

1. Dispenser Control Board

This component of your Electrolux dispenser is the foundation on which other components function. Ensure that you troubleshoot all other components of your dispenser before the dispenser control board. If all other components check out, you may need to hire a professional to fix the control board.

2. Dispenser Switch

Your ice dispenser needs a certain amount of voltage to function and it is supplied by the dispenser switches. In this light, ensure that none of the dispenser switches are defective.

To know a faulty ice dispenser switch, carry out a continuity test using a multimeter. If the multimeter reading indicates that there is no continuity, get a new dispenser switch.

3. Door Switch

As you open the door of your Electrolux refrigerator door, the ice dispenser and water dispenser goes off. The door switch allows the dispenser to come on when needed.

To determine the working condition of the door switch, you have to perform a continuity test and it will tell you if you need to replace the door switch.

4. Auger Motor

As the auger motor rotates the blade, ice is pushed to the dispenser chute. So, if you have a defective auger motor, ice cannot be pushed forward and nothing will get to the chute.

To know if the auger motor is faulty, detach the ice bucket and then rotate the bucket auger with your hands. If you do not feel any resistance, the auger motor is working properly. To be doubly sure of the auger motor working condition, run a continuity test. If the multimeter reading does not show any sign of continuity, get a new auger motor.

[amalinkspro type=”showcase” asin=”B08F6SRKQ6″ apilink=”https://www.amazon.com/dp/B08F6SRKQ6?tag=refrigeratorsreviewed-20&linkCode=osi&th=1&psc=1″ new-window=”true” addtocart=”true” nofollow=”true” sc-id=”6″ imgs=”LargeImage” link-imgs=”false” specs=”【Perfect Fits】： Fire Burn Pot, Hot Rod Ignitor, Auger Motor and Grill Induction Fan Kit Can work well with most Traeger and Pit-boss pellet grills except PTG,If the additional screws we sent to you cannot work normally, please use your original old screws to complete the installation and achieve normal operation.Compatible Model: Texas Elite Series, Pro 34,Pro 22,Fits all Traeger grill models Traeger 070, 075, all Camp Chef smoker grill,Lil Tex Elite Series, Pit Boss Wood Pellet Grills .” btn-color=”#ff9900″ btn-text=”Buy on Amazon” alignment=”aligncenter” hide-prime=”0″ hide-image=”0″ hide-price=”0″ hide-button=”0″ width=”600″]Auger Motor,Grill Induction Fan Kit, Fire Burn Pot and Hot Rod Ignitor,Replacement Parts with Screws and Fuse for Pit Boss and Traeger Wood Pellet Grill,Drive Motor and Combustion Fan Ignitor Kit Fits[/amalinkspro]

Electrolux Refrigerator Water Dispenser Sticks – Solutions

If the button of your Electrolux refrigerator water dispenser sticks, follow the steps below to fix it:

1. Turn Off the Power Supply

The button of your Electrolux dispenser may stick if you press it too hard. If you notice that the button is stuck, do not bother to continue pressing it as most people would usually do. Instead, disconnect the refrigerator from the power supply and give a 15-minute interval before plugging it back in.

The reason for this simple action is because sometimes a power outage can unstick the water dispenser button.

2. Close the Refrigerator Door

If the dispenser button gets stuck and the door of the refrigerator is open, it will not release water. So, ensure that door is closed and the button will be unstuck.

3. Deactivate the Lock Mode

The Electrolux refrigerator water dispenser is built with a lock mode, which means the dispenser would not work when activated. If the lock mode of your Electrolux dispenser is activated, it may appear like the button is stuck.

Go to the lock mode settings and check if it is activated. If it is, deactivate it, so you can use your dispenser without any glitches.

4. Check the Electrical Wiring

At the back of the Electrolux refrigerator, you will find a set of wires that are connected to transmit signals to other compartments, indicating when to open or close. As with all electrical wiring, you will need to replace them after some time because they may have lost their conductivity or be burnt.

The wiring is quite tricky, so it is best to hire a repairman to do the reinstallation for you.

5. Inspect the Light Button

You should know that the Electrolux refrigerator light button is stuck if the light does not switch on when the refrigerator is opened. If the light button is the same level as the wall of the refrigerator, then it is stuck.

Release the light button by pulling the small lip on the switch. Keep pressing and releasing the switch until you are sure it won’t stick again.

[amalinkspro type=”showcase” asin=”B00LGUHE02″ apilink=”https://www.amazon.com/dp/B00LGUHE02?tag=refrigeratorsreviewed-20&linkCode=osi&th=1&psc=1″ new-window=”true” addtocart=”true” nofollow=”true” sc-id=”6″ imgs=”LargeImage” link-imgs=”false” specs=”Manufacturer Model #242074201″ btn-color=”#ff9900″ btn-text=”Buy on Amazon” alignment=”aligncenter” hide-prime=”0″ hide-image=”0″ hide-price=”0″ hide-button=”0″ width=”600″]Electrolux 242074201 Dispenser-Module[/amalinkspro]

Why Does My Electrolux Refrigerator Water Dispenser Turn On by Itself?

If you notice that your water dispenser automatically turns ON, you may be tempted to think that the motherboard is responsible for that anomaly. However, if you observe closely, you will notice that even if you deactivate the control lock, the unit will still be dispensing.

The dispenser switch is responsible for the anomaly. In its defective state, the dispenser switch feels you are holding down the pad when in actuality, you are not. Order a new pad and the automatic turning ON problem will be a thing of the past.

Get Instant Help — Ask An Experienced Verified Appliance Technician

Need expert help? Click here to use the chat box on this page to speak with a verified appliance technician right away. No need for expensive in-home service calls. No appointments. No waiting.