Frigidaire Refrigerator Control [Issues and Solutions]

Frigidaire refrigerator control allows you access and control over certain parts of the refrigerator. However, if there are issues, the refrigerator may stop working altogether.

Frigidaire Refrigerator Control

Frigidaire Refrigerator Control Board Test – Steps

To accurately test the control board on a Frigidaire refrigerator, do the following:

Step 1

Get a large flat-head screwdriver for pulling the board out. Also, get a digital multimeter for testing resistance.

Remove the bottom grille of the unit to gain access to the control board. If you have a bottom freezer french-door refrigerator model, pull the drawer out before removing the grille.

Step 2

Pry the housing of the main control board loose and draw it toward you in order to detach it. Next, test the voltage supply. Because you need the refrigerator to be plugged into electric power in order to carry out this test, be sure not to touch any part of the board with your bare hands.

Step 3

Set the multimeter to volts DC. that would be the V on the multimeter that has the straight and dotted lines over it.

Take the red probe of the multimeter and insert it into the harness at the top of the board, to the left. You will see five wires coming out of it; insert the probe into the second wire from the left.

Insert the black probe of the multimeter into the third wire from the left, next to the one with the probe inserted into it.

Step 4

The multimeter should register between 12 volts and 14 volts if everything is working as it should. If this is not the case, the control board may have failed.

To be sure, run the same test on the other wires and confirm that the board is receiving and delivering power to the refrigerator. Otherwise, consider replacing it.

See also  Samsung Refrigerator Won’t Fit through Door [Simple Solution]

This video is showing a test of the control board where the control panel on a refrigerator is not working…

How to Reset Frigidaire Refrigerator Control Panel

To reset the control panel on a Frigidaire refrigerator, press the Power Freeze and Power Cool pads on the panel and hold them for a few seconds. The refrigerator will kick into action shortly.

For a hard reset, switch it off and disconnect it from electric power. If you cannot unplug it from the wall outlet, turn off the circuit breaker that controls it.

Allow the refrigerator to remain switched off for about thirty seconds and without electric power for about five minutes. Afterward, reconnect it to power and switch it back on.

Where Is the Air Damper Control on a Frigidaire Refrigerator?

The air damper control on a Frigidaire refrigerator is in the fresh food section. It is at the top of the wall, to the left. It opens to allow just enough cold air into the refrigerator from the freezer and closes to shut off the air so the refrigerator does not freeze.

Where Is the Main Control Board on a Frigidaire Refrigerator?

The main control board on a Frigidaire refrigerator is under the unit. It is behind the bottom grille in front of the refrigerator.

Check out these other articles…

Frigidaire Refrigerator Smells Like…[Solved]

Frigidaire Ice Maker Stuck [How to Fix]

Frigidaire Refrigerator Is Loud [How to Fix]

Frigidaire Refrigerator Bulb [Issues & Solutions]

Frigidaire Refrigerator Air Filter [How to]

LG Refrigerator Filter [Issues & Solutions]

How to Replace a Frigidaire Ice Maker [Quick Guide]

How to Replace the Main Control Board on a Frigidaire Refrigerator

To replace the main control board on a Frigidaire refrigerator, take the following steps:

Step 1

Pull out the power cord of the refrigerator from the wall outlet. Flip the switch of the circuit breaker that controls the refrigerator if you cannot reach the power cord.

Step 2

Find the main control board of the unit. If there is a grille or cover over it, pry it loose with a flat-head screwdriver.

Make a note of the wire connectors on the board before disconnecting anything. If it helps, take photos for easy reference.

Step 3

Remove the test port plug on the board. Then, unlock the retaining tab to be able to remove the board. Do this by depressing the tab.

See also  Frigidaire Refrigerator Dispenser Problems [Solved]

Step 4

Pull out the defective board and put the new one in its place. Align the new board inside the housing and push it gently until it snaps into place.

Step 5

Connect the wire harnesses or connectors to the right terminals. Consult your photos if you took any so that you make the connections correctly. Then, put the test plug back in place.

Step 6

Next, place the housing of the main control board back on its tracks and push it in until it locks in place. Afterward, reinstall the bottom grille.

Plug the refrigerator back into the outlet or power up the circuit breaker.

Frigidaire Freezer Control Panel Flashing H1 – Quick Fix

If you find the control panel on your Frigidaire freezer flashing h1, you need to lower the temperature in the freezer. The indicator is letting you know that the internal temperature is too high. The same applies if you see h flashing on the display.

Close the door of the freezer fully and press the temperature alarm reset button. This should mute the beeping of the alarm but the icon will stay illumined until the internal drops to a food-safe level.

This may take some time because for the error to be displayed and the alarm activated, the temperature had exceeded 26 degrees Fahrenheit.

Ensure the door stays closed and sealed tightly. Additionally, don’t hold it open for too long as it has the same effect on the refrigerator as not closing it fully.

Frigidaire Refrigerator Control Panel Locked – Solved

If the control panel of a Frigidaire refrigerator is locked, unlock it by finding the Control Lock key on the panel. You may find it beside the Light On/Off pad. Press it and hold it until the tiny LED light beside the lock goes off.

If unlocking it the conventional way does not work, disconnect the refrigerator from electric power, wait about a minute, and plug it back into power. Then, try unlocking it again.

However, if the panel still does not work, you may need to replace the board that controls it. Contact Frigidaire to report the issue and request service.

Frigidaire Refrigerator Temperature Control Problems – How to Fix

If your Frigidaire refrigerator is having a hard time maintaining the set temperature, clean the condenser coils and the compressor. Dirty coils and compressors build heat easily which compromises the refrigerator’s internal temperature. So clean them at least once a year.

See also  Age of a Maytag Refrigerator [Quick Guide]

However, if cleaning them does not solve the problem, consider resetting or adjusting the set temperatures of both sections – 37 degrees Fahrenheit for the refrigerator and 0 degrees Fahrenheit for the freezer.

If the problem continues, check the door gasket for proper sealing. Use the dollar trick where you close the door of each compartment on a dollar bill and try pulling it out. If you can, replace the gasket.

Consider how often you close and open the doors. Also, consider the amount of food you store in the unit each and whether or not you put hot food in it. Additionally, look at the air vents. They should be open and nothing should obstruct them.

If all of the above doesn’t fix the problem, then there may be something wrong with the temperature controls. You may have to replace them. Contact Frigidaire or a trusted appliance technician for this job.

If you are going to do this fix yourself, this video is a step-by-step guide to replace the cold control on a Frigidaire refrigerator…

Frigidaire Refrigerator Temperature Control Flashing 4 – Quick Fix

When there is no power supply to the damper control in the refrigerator, you see the error code 4. Make sure the voltage going to the damper is up to 120vac. If it is, the damper needs a replacement because it is malfunctioning even though it is getting enough power.

But if the voltage is not enough, then the main control board is the problem. It is no longer sending the required amount of voltage to the damper. Replace the board.

Where Is the Control Panel on a Frigidaire Refrigerator?

The control panel on a Frigidaire refrigerator is right in front of it, on the door. It is the part where you have a small screen for displaying set temperatures and other functions. It also has buttons for adjusting temperature, choosing ice or water if you have a dispenser, choosing cubed or crushed ice, and so on.

Where Is the Control Lock Button on a Frigidaire Refrigerator?

The Control Lock button on a Frigidaire refrigerator beside the Light On/Off button on the control panel.

If you don’t find this easily, see if there is a tiny red light anywhere on the control panel. Once you find the light, you have found the button.


It is important to fix a Frigidaire refrigerator control issue as quickly as possible. You may find it frustrating to use the refrigerator if the controls are not functioning optimally.

Luckily, this article deals with different possible issues with the controls. You will find it easy to fix if you follow the steps here.

However, if you have a hard time sorting the issues out permanently, contact Frigidaire to report the issue and request service.

You also have the option of using our appliance technicians. Chat with any of them right away.

Get Instant Help — Ask An Experienced Verified Appliance Technician

Need expert help? Click here to use the chat box on this page to speak with a verified appliance technician right away. No need for expensive in-home service calls. No appointments. No waiting.