A Maytag refrigerator filter is an essential part of the unit, especially if there is an ice maker or water dispenser. This article is about filter problems and solutions.
Table of Contents
Maytag Refrigerator Filter Reset – Steps
If you replace the water filter in your Maytag refrigerator, it is crucial to reset the filter light. Most Maytag refrigerators do not automatically reset the filter light, so you have to do it manually. However, how you reset it will depend on the model of the Maytag refrigerator you own. Follow the instructions in the user manual or use this guide to do the job.
How to Replace a Maytag Refrigerator Filter
You will find Maytag refrigerator water filters either at the front bottom grille or inside the refrigerator, in the upper right-hand corner. How you replace the filter depends on the location and the type of filter. The refrigerator’s user manual has all the instructions you need to replace the filter.
However, if you cannot find the manual, check the location of the filter. Also, check the type. If you are using an Everydrop refrigerator water filter, which is the recommended type for Maytag refrigerators, the number on the packaging tells you the installation procedure.
Everydrop 1
Find the filter housing in the upper right-hand corner inside the refrigerator or grille at the bottom front. If it is at the bottom, turn the filter handle in the right direction to loosen it before pulling it out. Throw the old one away and get the new filter.
Remove the cover on the O-rings and insert the filter, ensuring the arrow points upward. Do not force it into position; turn the filter to align the notches with the grooves if it is difficult. Once in place, run water through the dispenser or water supply line to flush the system.
Everydrop 2
Once you locate the water filter housing, open the door and pull the filter downward. Next, turn the filter to the left before pulling it out. Throw the old filter out and get the new one. Remove the cover on the O-rings and insert the filter, ensuring the arrow points upward.
As you insert it, the filter should start to rotate, so turn it to the right to lock it in place. Close the filter housing door and run water from the refrigerator to flush the system.
Everydrop 3
This filter goes into the housing at the front bottom of the refrigerator. There is an eject button for removing the filter, so depress the button to release the filter. Pull it out of the housing when it is free. Next, turn the filter cap to the left or counterclockwise and pull it off. Discard the old filter, get the new filter, and remove the cover on the O-rings; check to ensure the rings are in place after removing the cover.
Place the filter cap on the new filter, ensuring to align the ridges. Now, turn the cap to the right or clockwise to secure it. Insert the filter into the housing at the bottom, ensuring the arrow points to the left. Once you correctly insert it, the eject button you pushed in earlier should pop out again. Then, run water from the unit to flush the system.
Everydrop 4
Find the filter in the upper right-hand corner of the interior part of the refrigerator. Locate the tab securing the filter cover; if the cover has the tab on the bottom, pull the lever forward and down to open the cover. But if the tab faces outward, depress it and pull down the cover.
Twist the filter counterclockwise or to the left and remove it. Throw it out and get the new filter for installation. Check the filter opening for a cap and when you find it, turn it to the left and pull it out. Line the filter with the grooves when installing it, push it in place, and turn it clockwise or to the right. After that, push the filter up, lock it in place, and close the filter housing door. Run water from the unit to flush the system when everything is in place.
Everydrop 5
The filter installs in the bottom grille. When you locate the housing, you will see a cap or handle sticking out from the grille. Turn the handle to the left or counterclockwise until it is vertical. The filter is loose when it is in that position, so you can pull it out. Slide the filter cap or handle off the old filter, keep it, and throw the old filter away.
Next, get the new filter and remove the cover on the O-rings. Fix the cap to the end of the filter and insert it. When inserting it, ensure the cap sits vertically before pushing the filter into the housing. When it is entirely in, turn the cap or handle to the right or clockwise until it is horizontal. Finally, run water from the refrigerator to flush the system.
Note: These steps apply to other compatible water filter types for Maytag refrigerators. The most crucial part is finding a suitable filter according to the refrigerator model and the installation method. Once you get the right type, follow the steps that apply to install the filter. Read this article to locate the filter in your unit.
How to Replace the Air Filter in a Maytag Refrigerator
Maytag refrigerators have two ways to install air filters. You must locate the air filter inside the refrigerator; the user manual comes in handy to find the exact location. Some models have an air filter behind the vent cover, illuminated by the LED lights. The cover is on the inside back wall, close to the middle of the unit’s wall. Remove the covering on the vent cover and pull out the old air filter. Put the new filter in place and snap it into position.
Other models have the air filter behind the vent door, on the inside back wall close to the top of the refrigerator. Lift the vented door to open it and remove the old air filter. Fix the new filter in place and snap it into position.
Check out these other articles…
Maytag Refrigerator Cooling [Problems, Solutions & Guide]
Maytag Refrigerator Stuck [Problems Solved]
Maytag Refrigerator Not Making Ice [Proven Solutions]
Maytag Refrigerator Making Ice [Problems & Solutions]
Maytag Refrigerator Smells [Proven Solutions]
Maytag Refrigerator Water Filter Housing Leaking – Fixed
If you find the water filter housing in a Maytag refrigerator leaking, you may have to replace it. But before replacing it, check the water filter to ensure it is in good working condition. Ensure the head is not leaking and it is correctly installed. This article on a Maytag refrigerator water filter housing leaking shows you how to fix the problem.
Maytag Refrigerator Water Filter Leaking – Quick Fix
The water filter may not be properly installed in the filter housing. Another possibility is that the filter head is damaged. Also, there is high pressure built at the connection point. The force from the main water source may be too much, pushing the filter out.
Remove the water filter and check the head. If there is any damage to that part, the only solution is to replace the filter. You cannot fix the damaged head, so purchase a new filter and ensure it is compatible with the Maytag refrigerator. But if the head is not damaged, carefully and correctly install the filter. Ensure the notches correctly align with the grooves. If the filter continues leaking, you may have to purchase a new one because the old one may be damaged.
Maytag Refrigerator Water Filter Not Working
If the water filter is not working, replace it. The filter may be too old for use, and the dirt clogging it restricts the flow of water. If you recently replaced the filter, it may be the wrong type, is incorrectly installed, or is damaged. If it is incorrectly installed, you can easily fix the problem. But if it is the wrong type of is damaged, you have to replace it.
When you get the new one, ensure it is the correct type for the specific Maytag refrigerator model and the O-rings are intact. If the filter takes too long to work, remove it and soak it for a few minutes in water. Sometimes, the filter has a harder time soaking than usual, so you may have to soak it manually so that it can work quickly.
Dispense a few gallons of water from the refrigerator after replacing the filter so that you can flush the system. Trapped air can stop the filter from working; only flushing the system can fix it.
Maytag Refrigerator Water Filter Noise – Solved
Dirt, debris, or any obstruction on the head of the filter can cause it to become noisy. So, if the water filter in your Maytag refrigerator is noisy, remove it and check the head. Clean it if there is dirt, and remove every debris that can cause noise. Next, fix the filter back in place and try the dispenser again.
If the noise persists, remove the filter and fix a bypass plug. Try the unit again; a lack of noise means the filter is the problem. So, you may want to replace it. But if the refrigerator remains noisy even with the bypass plug, check other possible causes.
Maytag Refrigerator Filter Stuck – Solution
There are several ways to install a new refrigerator water filter in Maytag refrigerators. In the same vein, there are several ways to remove them. So, if a filter is stuck, removing it depends on the installation method.
Bottom Grille Eject Button or Quarter-turn Filter Type
If your filter fits in the front bottom grille, there may be an eject button. Some turn before you can remove them. If there is a button, ensure you are fully pressing the button all the way. Push it until the filter loosens from the housing. It is usually easy to remove such a filter.
Press and hold the button until the filter comes out, or push the filter and push the button if the filter is stuck. Turn off the refrigerator and remove the front bottom grille if that does not work. Doing that gives you more access to the filter.
Press the button again and check to see if the filter moves. If it does, push it in again and push the button one more time, making removing it easier. However, get professional help if the filter remains stuck.
But if the filter has a handle or cap, give it a quarter-turn counterclockwise. Before doing that, the cap should be horizontal to the right. After turning it a quarter, it should be vertical. Once vertical, pull the filter out; it should be loose at this time.
Get a small cloth and place it over the cap if the filter is stuck. Next, get a pair of pliers and hold the filter cap. Give the cap a turn in the right direction; consider removing the grille to give you better access to the filter. Grasp it gently but firmly with the pliers and pull the filter out. Do not use too much pressure to avoid damaging the water system.
Interior Refrigerator Door Open or Push Button Filter Type
If the filter is the type that fits in a compartment or pops out, close the filter housing door and open it again. Next, turn the water to the refrigerator off and dispense leftover water from the water supply line or dispenser. If there is built-up pressure, dispensing the water fixes it. Turn on the water and try removing the filter again.
You may also have to rearrange shelves and items to allow you to remove the filter if it is the pull tab or a push-button type. The filter housing door must be fully open before attempting to remove the filter. Turn it to the left or counterclockwise to remove it. Doing that should loosen the filter for easy removal. If the filter remains stuck, get professional help.
Maytag Refrigerator Water Filter Slow – Quick Fix
The filter may be obstructed with dirt, or you may not have correctly installed it. So, if your Maytag refrigerator water filter is slow, replace it if it is older than six months. But if it is new, remove the filter and check it for dirt or any obstruction. Clean the filter head and put it back in place. If the problem continues, replace the filter. Ensure you install it correctly following the instructions in the user manual.
Recap
Follow the steps in this article to fix the Maytag refrigerator filter problems. If the filter is stuck, the water pressure may be too high. And if the filter light does not go off after replacing the filter, you have to manually reset it.
If you have trouble fixing the filter issues in your Maytag refrigerator, contact the Maytag Service Center, report the issues, and request service. This is especially true if you have an active warranty on the unit. Alternatively, employ the services of a qualified appliance technician to check the refrigerator and fix it permanently. Run regular maintenance checks on your refrigerator to keep it in optimum condition.
Get Instant Help — Ask An Experienced Verified Appliance Technician
Need expert help? Click here to use the chat box on this page to speak with a verified appliance technician right away. No need for expensive in-home service calls. No appointments. No waiting.