How To/Solutions To Problems

Indesit Refrigerator Dispenser Problems [Solutions]

This article will help you to resolve the Indesit refrigerator dispenser problems you may have been grappling with for a long time.

Frigidaire FFHT1425VV 28 Inch Freestanding Top Freezer Refrigerator (Brushed Steel)

Indesit Refrigerator Water Dispenser Not Working – What to Do

If your Indesit refrigerator water dispenser is not functioning properly, troubleshoot the following parts and fix any you find to be defective:

1. Water Tank

If there is no water in the water tank, nothing will flow to the dispenser, and you may think that is an electrical problem. So, the first part of your Indesit refrigerator water dispenser to troubleshoot if you notice a problem is the water tank.

If the water tank is empty or almost empty, fill it up and the issue will be resolved.

2. Dispenser Control Board

The dispenser control board is the heart of the dispenser and every electrical component of the dispenser is wired to it. If the dispenser control board stops working, the components wired to it will stop functioning as well.

If you notice two or more components of your Indesit refrigerator dispenser are not working, the dispenser control board is most likely responsible. Test the dispenser control board to know if it needs to be replaced.

3. Water Tube

The water tube is the channel through which water gets to the dispenser. If the water tube freezes up, water will not flow to the dispenser, and you know there is a problem.

To know if the water tube is the cause of the Indesit refrigerator dispenser problems, use a hairdryer to pass air through the water tube. If air does not get to the other end of the tube, it means the tube is frozen and needs to be thawed.

After thawing the frozen water tube, ensure that the freezer temperature is kept between 0 and 10 degrees Fahrenheit. This will prevent the water tube from freezing up again or becoming too warm.

4. Water Inlet Valve

As the water pressure forces the water inlet valve to open, water flows to the dispenser. If the water pressure is not up to 20 psi, it cannot open the water inlet valve, and water will not flow to the dispenser.

Also, if the water inlet valve is broken or twisted, the valve will not open.

To know if the water inlet valve is responsible for the Indesit refrigerator dispenser problems, test it for continuity. The result of the test will inform you whether to replace the water inlet valve or not.

5. Dispenser Switch

The voltage that powers the dispenser is supplied by the dispenser switch. If the dispenser switch breaks down, the dispenser will not receive power.

You can test the dispenser switch for continuity to determine if it needs to be replaced or not.

6. Water Filter

The water filter sieves out dirt from your drinking water. If the pores of the water filter are blocked with dirt, water will not flow to the dispenser.

To restore water flow to the dispenser, replace the water filter once you notice it is clogged.

Note: Before you start to troubleshoot the Indesit refrigerator, ensure it is not connected to the power source to prevent electrocution.

Check out these other articles…

Fisher & Paykel Fridge Freezing Everything [Quick Fix]

Samsung Ice Maker Not Dumping Ice [How to Fix]

Magic Chef Refrigerator Freezing Everything [Solution]

How to Remove Glass from Samsung Fridge [Quick Guide]

Dometic Fridge Freezing Everything [How To Fix]

Neff Refrigerator Dispenser Problems [Solved]



How to Clean Indesit Refrigerator Water dispenser

To clean your Indesit refrigerator dispenser, do the following:

Step 1: Disconnect the Power Cord

Before you start cleaning the Indesit refrigerator dispenser, ensure you disconnect the power cord from the wall outlet to prevent electrocution.

Step 2: Activate the Dispenser Lock Mode

After observing the safety protocol to avoid electrocution, activate the dispenser lock so that water does not spill all over the floor.

Step 3: Shut Down the Water Supply

The next thing is to shut down the water supply providing water for the dispenser. This will allow you to flush the dispenser system with white distilled vinegar.

Step 4: Add Vinegar

Not only is distilled vinegar a good cleaning agent, but it is also non-toxic, so you will not have any health concerns if you inadvertently consume it.

Place a tiny funnel in one end of the water tube and pour two or three cups of distilled vinegar into the water tube. The vinegar solution will flow through the water tube to the dispenser. Allow the vinegar to sit for about ten minutes to dislodge dirt in every corner of the dispenser.

Step 5: Flush Out the Vinegar Solution

Place a bowl beneath the nozzle of the water dispenser, and turn on the water dispenser to flush out the vinegar solution. Ensure there is no vinegar residue left in the dispenser.

Once you have successfully removed the vinegar, use a toothbrush to scrub the water tube and sprout area of the dispenser. For thorough cleaning, dip the brush in the vinegar before scrubbing the dispenser parts.

Step 6: Reconnect the Water Supply

After thoroughly cleaning the dispenser, reconnect the water supply tube back to its original position. Also, turn on the water inlet valve, so water can flow to the dispenser. Flush the dispenser system for the second time and wipe the exterior of the dispenser with a damp cloth. Check out the video below to learn more about cleaning a refrigerator dispenser…

Finally, if you have more questions about fixing your Indesit refrigerator dispenser, feel free to ask the appliance technicians on our website via the live chat feature.